• 0769-81619276

Spec.

Part Summary Circuit Application Download
WS2812S(W/B)
•  Model No.:WS2812S,WS2812S-B;
 
• “5050 Chip LED with Driver+6PIN”Intelligent control integrated LED light source
 
• Black and White version are avaliable; 
 
• The control circuit and the LED share the only power source.
 
• The gray levels of each pixel are of 256 levels
 
• Refresh frequency reaches to 400Hz/s.
 
• When the refresh rate is 30fps, cascade numbers are far more than 1024 points.
 
• Data transmitting speeds is up to 800Kbps.
WS2812S(W/B) Download
WS2812B/C/Mini
• Model:WS2812B,WS2812B-B,WS2812C,WS2812C-B,WS2812B-Mini;
 
• “5050/3535 Chip LED with Driver+4PIN”Intelligent control integrated LED light source.
 
• White and black version are avaliable;
 
• The control circuit and the LED share the only power source.
 
• The gray levels of each pixel are of 256 levels
 
• Refresh frequency reaches to 400Hz/s.
 
• When the refresh rate is 30fps, cascade numbers are far more than 1024 points.
 
• Data transmitting speeds is up to 800Kbps.
WS2812B/C/Mini Download
WS2812B

WS2812B is a intelligent control LED light source that the control circuit and RGB chip are integrated in a package of 5050 components. It internal include intelligent digital port data latch and signal reshaping amplification drive circuit. Also include a precision internal oscillator and a 5V voltage programmable constant curre-nt control part, effectively ensuring the pixel point light color height consistent.

The data transfer protocol use single NZR communication mode. After the pixel power-on reset, the DIN  port receive data from controller, the first pixel collect initial 24bit data then sent to the internal data latch,   the other data which reshaping by the internal signal reshaping amplification circuit sent to the next cascade  pixel through the DO port. After transmission for each pixel,the signal to reduce 24bit. pixel adopt auto resha-ping transmit technology, making the pixel cascade number is not limited the signal transmission, only depend on the speed of signal transmission.

    LED with low driving voltage, environmental protection and energy saving, high brightness, scattering angle is large, good consistency, low power, long life and other advantages. The control chip integrated in LED   above becoming more simple circuit, small volume, convenient installation.

WS2812B Download
WS2813A/B/Mini
• Model:WS2813B,WS2813B-B,WS2813B-Mini;
 
• Intelligent control integrated LED light source
 
• The control circuit and the LED share the only power source.
 
• The gray levels of each pixel are of 256 levels. Refresh frequency reaches to 2KHz/s.
 
• Dual-signal wires version, signal break-point continuous transmission.
 
• When the refresh rate is 30fps, cascade numbers are far more than 1024 points.
 
• Data transmitting speeds is up to 800Kbps.
WS2813A/B/Mini Download
WS2815B/Mini
• Model:WS2815B,WS2815B-B,WS2815B-Mini;

• 5050/3535 Chip LED with Driver+4PIN Intelligent control integrated LED light source. • Intelligent control integrated LED light source

• The control circuit and the LED share the only power source.

• The gray levels of each pixel are of 256 levels。Refresh frequency reaches to 2KHz/s.

• Dual-signal wires version, signal break-point continuous transmission.

• When the refresh rate is 30fps, cascade numbers are far more than 1024 points.

• Data transmitting speeds is up to 800Kbps.

WS2815B/Mini Download
WS2862B/Mini

1).Pixel Gray Update from 256(8bit) to 65536(16bit):

Can get a multiple color level and create gorgeous image easily!

Super suitable for high resolution display application!

2).Port Refresh Frequency update from 400HZ to 2000HZ:

Even under high speed camera ,You can get a much faster dynamic effect without flicker as well.

3).High precision constant current output,precision within 3%;

4).Double signal wire version:

Own one set spare signal wire(signal can jump to transfer),one signal failure then switch to spare signal,which guarantees the stability!

5).Up to 24V port pressure (IC only);

Support 5050 and 3535 LED package,which allows you to make more applications in small space with high density LED !

WS2862B/Mini Download
WS2851 LED
• With WS2811 IC and RGB chip integrated in a 5050 component, the WS2811 IC not only controls the integrated RGB5050, but also controls the external RGB5050 LEDs.
 
• 12V Voltage of Output port.
 
• With VR-tube built in 5050 components, only one resistor is needed to make it work when voltage is below 24V.
 
• Built-in Signal Reshaping circuit, any IC receives the signal, and then re-exported through the waveform reshaping to ensure that the waveform distortion of the circuit will not accumulate.
 
•  Built-in Power-on reset circuit and Power-off reset circuit, PWM control side can achieve 256 gray level adjustment.
 
• The reception and decoding of cascading data can be completed by a Serial Interface.
 
• Transmission distance between any two points is no more than 10 meters, no need any additional circuit.
 
Much smaller and more space-saving while applied in LED flexible strips.
 
WS2851 LED Download
WS2850-W
• Model No.:WS2850(White Version);
 
• To provide better service for our customer,we designed the high brightness 5050 RGB LED;“
 
• After open the package, the LED should be kept at 25oC, 65 % RH environment or less.  
 
• The LED should be soldered within 6 hours after opening the package.
 
• The LAMP  LED is an ESD sensitive device. All the equipment and machine must be  properly grounded.
 
• Strongly recommend design the board according setting current other than setting voltage .if you are really need setting voltage type please consider there may cause influence arise by difference voltage of difference LED
 
•The outer voltage change will bring the current index change .unsuitable design and current control,easy cause LED fail .for example excess current will cause LED life short or even burn down , too little electricity will cause lacking light
WS2850-W Download
WS2850-B
• WS2850-Black Verison;
 
• To provide better service for our customer,we designed the high brightness 5050 RGB LED;
 
• After open the package, the LED should be kept at 25oC, 65 % RH environment or less.  
 
• The LED should be soldered within 6 hours after opening the package.
 
• The LAMP  LED is an ESD sensitive device. All the equipment and machine must be  properly grounded.
 
• Strongly recommend design the board according setting current other than setting voltage .if you are really need setting voltage type please consider there may cause influence arise by difference voltage of difference LED
 
•The outer voltage change will bring the current index change .unsuitable design and current control,easy cause LED fail .for example excess current will cause LED life short or even burn down , too little electricity will cause lacking light

 

WS2850-B Download
WS2850-T
• Model No.:WS2850-Transparent Verison;
 
• To provide better service for our customer,we designed the high brightness 5050 RGB LED;
 
• After open the package, the LED should be kept at 25oC, 65 % RH environment or less.  
 
• The LED should be soldered within 6 hours after opening the package.
 
• The LAMP  LED is an ESD sensitive device. All the equipment and machine must be  properly grounded.
 
• Strongly recommend design the board according setting current other than setting voltage .if you are really need setting voltage type please consider there may cause influence arise by difference voltage of difference LED
 
•The outer voltage change will bring the current index change .unsuitable design and current control,easy cause LED fail .for example excess current will cause LED life short or even burn down , too little electricity will cause lacking light

 

WS2850-T Download
WS2835
• Model No.:WS2835-3528 Verison;
 
• View angle:120 deg;
 
• The materials of the LED is InGaN; 
 
• Dimension:3.5mmx2.8mmx1.40mm SMT-LED;
 
• Lens Appearance:Clean like water,transparent;
 
RoHS complaint lead-free soldering compatible;
 
• Standard Packge:2000pcs per reel;
 

 

WS2835 Download
WS3535
• To provide better service for our customer,we designed the high brightness 3535 RGB LED;“
 
• After open the package, the LED should be kept at 25oC, 65 % RH environment or less.  
 
• The LED should be soldered within 6 hours after opening the package.
 
• The LAMP  LED is an ESD sensitive device. All the equipment and machine must be  properly grounded.
 
• Strongly recommend design the board according setting current other than setting voltage .if you are really need setting voltage type please consider there may cause influence arise by difference voltage of difference LED
 
•The outer voltage change will bring the current index change .unsuitable design and current control,easy cause LED fail .for example excess current will cause LED life short or even burn down , too little electricity will cause lacking light
WS3535 Download
WS3030
• To provide better service for our customer,we designed the high brightness 3030 RGB LED;“
 
• After open the package, the LED should be kept at 25oC, 65 % RH environment or less.  
 
• The LED should be soldered within 6 hours after opening the package.
 
• The LAMP  LED is an ESD sensitive device. All the equipment and machine must be  properly grounded.
 
• Strongly recommend design the board according setting current other than setting voltage .if you are really need setting voltage type please consider there may cause influence arise by difference voltage of difference LED
 
•The outer voltage change will bring the current index change .unsuitable design and current control,easy cause LED fail .for example excess current will cause LED life short or even burn down , too little electricity will cause lacking light
WS3030 Download
WS2801S

• Model No.:WS2801S(SOP14 Package);

• Supports both constant voltage and constant current drive mode

• 3-Channel Constant Current LED Driver With Programmable PWM Outputs

• Wide-range constant output current range 5~150mA

• PWM free-run capability(refresh rate 2.5KHz)

• Build in buffers to cascading data and clock to the next driver

• Maximum input clock frequency 10MHz

WS2801S Download
WS2811s

• Signal line 256 Gray level 3-channel Constant current LED drive IC

• Output port compression 12V.

• Gray level 256 can be adjusted and scan frequency not less than 400Hz/s.

• When the refresh rate is 30fps, high speed mode not less than1024 points.

• Send data at speeds of up to 800 Kbps.

WS2811s Download
WS2818A

• Signal line 256 Gray level 3-channel Constant current LED drive IC

• Built-in power-on reset and brown-out reset circuits.

• The gray levels of each pixel of 256 levels, and the refresh frequency reaches to 2KHz/s.

• Signal Break-point Continuous Transmission, any pixel’s failure, it won’t affect the whole display effect.

• When the refresh rate of 30fps, the cascade number are not less than 1024 pixels.

• Send data at speeds of 800Kbps.

WS2818A Download
WS2818B

• Signal line 256 Gray level 3-channel Constant current LED drive IC

• Built-in power-on reset and brown-out reset circuits.

• The gray levels of each pixel of 256 levels, and the refresh frequency reaches to 2KHz/s.

• Signal Break-point Continuous Transmission, any pixel’s failure, it won’t affect the whole display effect.

• When the refresh rate of 30fps, the cascade number are not less than 1024 pixels.

• Send data at speeds of 800Kbps.

 

WS2818B Download
WS2819S

• Signal line 256 Gray level 3-channel Constant current LED drive IC

• Built-in power-on reset and brown-out reset circuits.

• The gray levels of each pixel of 256 levels, and the refresh frequency reaches to 2KHz/s.

• Signal Break-point Continuous Transmission, any pixel’s failure, it won’t affect the whole display effect.

• When the refresh rate of 30fps, the cascade number are not less than 1024 pixels.

• Send data at speeds of 800Kbps.

WS2819S Download
WS2861S

• 16bit Data Gray-scale, 655365 colors full color display

• 2-wires, adding a back-up signal line to fulfill continuous transmission on the break-point.

• The gray levels of each pixel of 256 levels, and the refresh frequency reaches to 2KHz/s.

• Signal Break-point Continuous Transmission, any pixel’s failure, it won’t affect the whole display effect.

• When the refresh rate of 30fps, the cascade number are not less than 1024 pixels.

• Send data at speeds of 800Kbps.

WS2861S Download
在线客服
  • 兑换热线
    4008-259-775
  • 服务热线
    0769-81619276
  • Worldsemi
  • Spring
  • Aimee